Motorcycle Helmet Camera Mounts: How to Choose and Install One Safely

By Delilah Dawson

Motorcycle helmet camera mounts give you a stable, hands-free way to record your rides, whether you want a clean view of the road for review or footage for sharing. This guide walks through the main mount types, how to match one to your helmet, the installation steps, and the mistakes that cause shaky footage or safety problems. By the end, you will know how to pick and set up a mount that holds steady and leaves your sightlines alone.

Why the Mount Matters as Much as the Camera

Most riders focus on camera resolution and forget that the mount controls almost everything about the final image. A camera vibrating against a loose bracket will produce footage that looks worse than a cheaper camera on a solid mount. The mount also determines where the camera sits, how much of your helmet it blocks, and whether it stays put at highway speed. Treat the mount as part of the safety equipment decision, not an accessory you add at the end.

Shopping for one? See our guide: Shoei RF-1400 Full Face Motorcycle Helmet Review: Is It Worth It?.

Types of Motorcycle Helmet Camera Mounts

Helmet camera mounts fall into a few broad categories. Each attaches differently and suits different helmet designs.

Mount type	How it attaches	Best suited for	Main drawback
Chin mount	Bracket on the chin bar or front of a full-face helmet	Full-face and modular helmets with a flat chin area	Sits in the field of view and can affect breathing noise
Top or crown mount	Attaches to the top vent or a flat section of the shell	Open-face and three-quarter helmets, or wide-angle top views	Less stable at high speed if not secured well
Side mount	Bracket on the side shell, often with a swivel arm	Riders who want a profile or rear-quarter angle	Can interfere with visor operation or ear coverage
Adhesive or strap mount	Adhesive pad or strap system	Helmets without suitable mounting points	Adhesive can damage paint or shell coatings

Chin Mounts and Full-Face Helmets

Chin mounts are the most common choice for full-face helmets because they give a forward-facing view close to what you see. Manufacturers of many full-face helmets sell or specify compatible chin brackets, so check your helmet’s accessory list first. Some riders also use a mount that clamps to the chin bar’s vent area. Keep in mind that anything on the chin bar sits in your peripheral field, so position the camera where it does not obstruct the lower edge of your visor.

Top and Crown Mounts

A crown mount places the camera above your eyeline and can capture a wider, more cinematic angle. These work well on open-face and three-quarter helmets. They also suit riders who want to film with the visor down and avoid glare from the front. Because the camera sits high, wind load is greater, so a secure fastening system matters more here.

Step-by-Step: Choosing the Right Mount

Use this sequence to narrow your options before you buy anything.

Identify your helmet type: full-face, modular, open-face, or three-quarter.
Check the manufacturer’s accessory list or owner’s manual for approved mounting points and accessories.
Decide on your camera angle: forward view, rear quarter, or top-down.
Confirm the mount’s compatibility with your camera’s mounting standard, such as the common quick-release or threaded system.
Pick a fastening method, either screws, clamps, or adhesive, based on how permanent you want the installation to be.

Installation Steps for a Stable Mount

A correct installation makes the difference between smooth footage and constant vibration. Work slowly and check each connection.

Preparing the Helmet and Mount

Clean the mounting area with isopropyl alcohol and let it dry fully before attaching anything.
Inspect the helmet shell for cracks, thin spots, or existing damage around the mounting point.
Dry-fit the bracket and confirm it does not press against the shell in a way that could crack it.

Securing the Bracket

Tighten screws in small increments and in a cross pattern to distribute pressure. Do not overtighten, since this can deform thin plastic shells. If your mount uses adhesive, follow the manufacturer’s cure time, which is commonly listed in the packaging, before riding. Avoid using adhesive on shells where the manufacturer warns against modifications.

Checking Stability

Once installed, shake your head gently side to side and nod up and down. Watch the footage or live preview. Any wobble suggests the bracket or the camera’s attachment point needs tightening. Also confirm the helmet still seats firmly on your head and that the camera does not shift when you turn.

Factors That Affect Image Quality

Mount placement changes what you record. Keep these points in mind:

Height: A camera slightly above eye level captures the road with less of your own helmet in frame.
Angle: A small downward tilt helps keep the horizon level and the road in view.
Vibration: Rigid mounts transmit less movement, but overly stiff setups can pass on shell resonance.
Wind noise: Exposed mounts create more noise, which can be reduced with a windscreen or by lowering the camera.

Common Mistakes

Mounting to a helmet that the manufacturer does not approve for accessories.
Placing the camera in the visor’s sweep path or near the visor release.
Using adhesive on a shell with a protective coating that may be compromised.
Ignoring loose screws after the first few rides, especially after a fall or a long highway trip.
Choosing a heavy camera and mount combination that shifts the helmet’s balance and causes neck fatigue.

Tips for Better Results

Recheck all fasteners before every ride for the first several outings.
Record a test clip at a standstill and again at speed to compare stability.
Keep spare fasteners and a small hex key in your tank bag.
Remove the camera and mount after a crash and have the helmet inspected before reuse.

Recommended gear

A few supporting items make a helmet camera setup more reliable. Pick a mount that matches your helmet’s accessory system, and consider a small set of accessories to keep everything tidy.

GoPro Helmet Front Mount: A well-known, widely compatible front bracket for many helmet styles, useful when you want a forward-facing view. View on Amazon
GoPro Helmet Side Mount: Offers an alternative angle and fits many of the same camera systems. View on Amazon
GoPro Chest Mount Harness: Useful as a second angle or for capturing footage without relying on the helmet alone. View on Amazon

FAQ

Can I mount a camera to any motorcycle helmet?

Not always. Check the manufacturer’s accessory list first. Some helmets include mounting points, while others require adhesive or strap systems that may not be approved for the shell.

Will a helmet camera mount affect my helmet’s safety rating?

Attaching accessories can affect how a helmet performs in an impact, depending on the design and the manufacturer’s guidance. Consult the helmet manufacturer before modifying the shell.

Where is the best place to mount a camera on a full-face helmet?

Most riders choose a chin or front-center position for a forward view. Make sure the camera does not block the visor’s lower edge or interfere with your breathing.

How do I stop my helmet camera from vibrating?

Tighten all fasteners, use a rigid bracket, and avoid mounting to thin or flexible shell areas. Test with a head shake before riding.

Does a helmet camera affect wind noise?

Yes. Exposed cameras add turbulence. Lowering the camera or using a windscreen can reduce noise.

Can I use adhesive mounts on my helmet?

Adhesive can work, but it may damage paint or protective coatings and can be hard to remove. Confirm with the helmet maker before using it.

How often should I check my mount?

Check it before every ride during the first few outings, then at regular intervals and always after a drop or crash.

Should I remove the camera when I’m not riding?

Removing it protects the camera from weather and theft and prevents the mount from loosening through repeated stress.

Conclusion

A good motorcycle helmet camera mount balances stability, sightlines, and helmet compatibility. Start by confirming your helmet’s accessory options, then choose a mount type that fits your riding and filming goals. Install carefully, test for vibration, and recheck fasteners regularly. A well-chosen mount will keep your footage steady and your helmet doing its main job.

Ready to choose one?

About Delilah Dawson

Delilah researches and writes buying guides and how-to articles on motorcycle riding gear. Picks are based on product specifications, brand reputation and patterns in owner feedback, and are updated as new models come out.

About the author

Delilah Dawson

Delilah Dawson writes reviews and buying guides for Max Motorcycle Videos.