How to Put On a Motorcycle Cover: A Step-by-Step Guide for Riders
Learn how to put on a motorcycle cover the right way, from prep and fitting to securing it so wind and rain can't pull it loose. A clear, simple guide.
Updated November 2026
Putting on a motorcycle cover takes about two minutes once you know the right order. Done correctly, the cover sits snug over the bike, keeps dust, rain and sun off the paint and seat, and doesn’t flap or scratch in the wind. The steps below cover how to put a motorcycle cover on, including how to secure it so it stays put.
Prepare the Bike Before You Cover It
A cover traps whatever is already on the bike. Dirt and moisture underneath can scuff paint and hold dampness against metal, so start with a clean, dry machine.
Shopping for one? See our guide: How Often to Clean and Lube Motorcycle Chain (2026): Which Should You Choose?.
- Wash off road grime, bug residue and salt, then dry the bike thoroughly, paying attention to the seat, tank seams and exhaust.
- Let the engine and exhaust cool completely. A hot exhaust can melt or scorch synthetic covers.
- Fold down or retract mirrors if they stick out, and remove any loose accessories that could snag the fabric.
- Make sure the kickstand is planted on firm, level ground.
Step-by-Step: Fitting the Cover
- Find the front. Most covers are marked or shaped with a front end that has a larger opening for the handlebars and windscreen. Hold the cover up and confirm the orientation before you start.
- Lift it over the front. Drape the front of the cover over the windscreen and handlebars first, then work it back toward the rear.
- Center it over the seat. Pull the cover down both sides so the bike is evenly covered. Check that the tank and seat are fully under the fabric.
- Tuck the rear. Feed the back of the cover over the tail section and smooth it down so it hugs the rear fender.
- Route the tie-downs. Pull the straps or cords under the bike, typically around the frame or swingarm area, and clip or tie them so the cover stays taut.
- Check fit. Walk around the bike. The fabric should be snug without being stretched tight. Loose spots catch wind, so tighten any strap that lets the cover lift.
Securing the Cover in Wind and Weather
A cover that fits well in still air can still lift at highway-level gusts or in a parking lot. Focus on the points that catch air and the places where the fabric can rub.
- Use every tie-down point the cover provides, not just one or two.
- Check that the underside straps don’t rub against the chain, exhaust or wiring.
- If the cover has a lock cable or grommet, use it, since a secured cover is harder to pull off.
Tools and Supplies Checklist
You don’t need much, but having these on hand makes the job faster and the result more secure.
- Motorcycle cover sized for your model (check the manufacturer’s size chart before buying)
- Microfiber towel for drying the bike
- Tie-down straps or the cover’s built-in cords
- Small cable lock, if the cover has a lock point
Common Mistakes
- Covering a wet or dirty bike, which can trap moisture and grit against the paint.
- Putting the cover on a hot engine or exhaust.
- Skipping the tie-downs, which lets wind lift and flap the fabric.
- Using a cover that’s too small, which stretches seams and strains fasteners.
- Dragging the cover across the seat or tank, which can grind dirt into the finish.
Recommended Gear
- A properly sized motorcycle cover with built-in tie-downs helps prevent wind lift. View on Amazon
- A microfiber drying towel helps you remove moisture before the cover goes on. View on Amazon
- A compact cable lock gives you a simple way to secure the cover’s lock point. View on Amazon
FAQ
Can I put a motorcycle cover on a bike that’s still warm?
It’s better to wait until the engine and exhaust have cooled. Heat can damage some synthetic covers and can scorch fabric that touches the pipes.
Do I need to remove the mirrors to fit the cover?
Not always, but folding or removing protruding mirrors makes the cover sit flatter and reduces the risk of tearing. Check the cover’s fit guide for your model.
How do I know if the cover is the right size?
Measure your bike’s length, width and height, then compare those numbers to the manufacturer’s size chart. If you’re between sizes, choose the larger one only if it still has proper tie-downs.
Conclusion
To put on a motorcycle cover, start with a clean, cool bike, fit the front first, center the fabric, and secure every tie-down. Check the fit after you finish and tighten anything that lets air lift the cover. A few minutes of care keeps your bike protected through wind, rain and storage.
Related reading
- Exhaust Pipe Cover Motorcycle Guide: How to Choose and Fit One (2026)
- Wind Rider Motorcycle Seat Cover: Fit, Use and Buying Tips for Riders
- Seat Cover Motorcycle Replacement: 6 Steps to Fit a New One (2026)
Ready to choose one?
