We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

Motorcycle Helmet Cover Sewing Pattern: Steps to Make a Fitted One

Learn how to use a motorcycle helmet cover sewing pattern to make a fitted, weather-resistant helmet cover. Covers fabric, measuring, cutting and finishing step

Updated November 2026

A motorcycle helmet cover sewing pattern gives you a set of cut pieces that wrap around your helmet and hold a fitted, protective shell in place. With the right fabric, a few accurate measurements and careful seam work, you can make a cover that keeps dust, rain and sun off your helmet when it is parked or stored. This guide walks through choosing materials, measuring, cutting and sewing.

Choose Materials Before You Cut

Pick a fabric that resists UV, moisture and abrasion. Many makers use a coated polyester or a lightweight nylon ripstop, since both hold their shape and shed water. Avoid cotton, which absorbs moisture and can hold grit against the shell. Lining is optional, but a soft fleece or quilted layer helps keep the cover from scratching a painted or matte helmet.

Shopping for one? See our guide: Shoei RF-1400 Full Face Motorcycle Helmet Review: Is It Worth It?.

Match your thread to the fabric. Use bonded nylon or polyester thread in a size suitable for your machine, and choose a longer stitch length, around 3 mm, so seams stay flexible when the cover is pulled on and off.

Measure Your Helmet Accurately

Most sewing patterns for helmet covers are drafted around a reference circumference. Measure your helmet at its widest point, about one inch above the eyebrow line, and record the front-to-back length over the crown. Compare these numbers with the finished measurements listed in the pattern, not just the size label. If your helmet is larger than the reference size, add ease to the seam allowances rather than enlarging the whole pattern.

Checking Fit Before You Sew

Make a quick mockup from scrap fabric or an old bedsheet. Pin the pieces together, pull the mockup over the helmet and check that the visor opening, vents and any antenna or intercom mounts are not blocked. Adjust the pattern before cutting your final fabric.

Cut and Sew the Panels

Cut each piece from the pattern, marking notches and grainlines. Pin the panels right sides together and sew with a 1/4-inch seam allowance unless the pattern states otherwise. Sew curved seams slowly and clip the seam allowance at tight curves so the fabric lies flat. Press seams open where possible to reduce bulk.

Adding Openings and Closures

Place the visor and vent openings using the markings on the pattern. Finish raw edges with a narrow hem, bias binding or a serger stitch to prevent fraying. For closure, a drawstring through a casing at the base or a hook-and-loop strip at the neck will hold the cover in place without shifting at speed. Keep any closure away from the visor opening.

Finish and Test the Cover

Turn the cover right side out and try it on the helmet. Confirm that it does not interfere with the visor mechanism, the release strap or any camera or Bluetooth unit. Make minor adjustments to the drawstring or hook-and-loop strip, then trim loose threads.

Common Mistakes

  • Skipping the mockup, which often leads to a cover that is too tight over the crown.
  • Using cotton or unfinished edges that trap moisture and grit against the helmet.
  • Placing a closure over a vent or visor gap.
  • Sewing with a stitch length that is too short, causing seams to split when stretched.
  • Forgetting that a helmet cover is for storage and transport, not a substitute for a properly fitted helmet.
  • Ripstop nylon fabric resists tearing and sheds water, making it a practical shell material for a helmet cover. View on Amazon
  • Bonded nylon thread holds up to UV exposure and moisture better than standard cotton thread. View on Amazon
  • Hook-and-loop strip gives a simple, adjustable closure that does not catch on the helmet shell. View on Amazon

For more on protecting your helmet and choosing the right accessories, see Motorcycle Helmet Camera Mounts: How to Choose and Install One Safely and Motorcycle Helmet Camera Setup: 6 Steps for a Stable, Clear View.

FAQ

Can I use any sewing pattern for a motorcycle helmet cover?

It is best to use a pattern drafted for helmet covers, since the openings and fit depend on helmet shape. A general hat or bag pattern will likely need significant changes.

What fabric works best for a helmet cover?

A coated polyester or ripstop nylon is a common choice because it resists moisture, UV exposure and abrasion. Avoid cotton, which absorbs water.

Should a helmet cover be used while riding?

No. A cover is meant for storage and transport. Wear your helmet without a cover while riding so the shell and fit are not affected.

Conclusion

A motorcycle helmet cover sewing pattern is a practical way to build a cover that fits your helmet and suits your storage needs. Measure carefully, test with a mockup and finish all raw edges to keep the cover durable. Take the time to check fit before cutting your final fabric.

Claire Whitaker

About Claire Whitaker

Claire Whitaker is part of our editorial team and reviews and edits our motorcycle riding gear guides, checking product details against manufacturer specifications and owner feedback.

About the author

Claire Whitaker
Claire Whitaker

Claire Whitaker writes reviews and buying guides for Max Motorcycle Videos.