How to Put GoPro Camera on Helmet: A Step-by-Step Guide for Riders

By Claire Whitaker

Updated November 2026

To put a GoPro camera on a helmet, you need a helmet-compatible mount, a secure attachment point on the shell, and a correctly aimed lens. Done right, the camera stays put at highway speed, shows the road ahead, and does not block your view or add risk. This guide walks through choosing the mount, installing it and checking the setup before you ride.

Choose the Right Mount for Your Helmet

Most GoPro helmet setups use one of three mount types: a chin mount, a top or side-shell mount that uses adhesive or a strap, or a bracket that attaches to a helmet’s existing accessory points. Chin mounts give the most natural angle for motorcycle footage but sit close to your line of sight. Shell mounts keep the camera higher and out of the way. Check that the mount is designed for your specific helmet shape, since a flat-backed mount will rock on a rounded shell.

Shopping for one? See our guide: GoPro Camera for Motorcycle Helmet: 4 Best Options Compared (2026).

Install the Mount and Camera Securely

Follow these steps for a stable install:

Clean the mounting surface with rubbing alcohol and let it dry completely.
Test-fit the mount without adhesive to confirm it sits flat and does not touch the visor, vents or shell seams.
Apply the adhesive pad or fasten the strap, pressing firmly for the time the manufacturer specifies, often around 24 hours for adhesive to fully cure.
Attach the GoPro to the mount and tighten all thumbscrews or clips by hand.
Give the camera a firm tug in each direction to confirm nothing shifts.

Never drill, screw or modify your helmet shell. Doing so can compromise the impact protection that the shell is certified to provide, and it may void the manufacturer’s warranty.

Set the Camera Angle and Placement

Aim the lens so the horizon sits in the upper third of the frame when you ride upright. Leave the front of the helmet visor and your peripheral vision completely clear. Check that the camera does not sit in the path of your head movement when you turn to check mirrors or shoulder-check traffic. A small tilt downward usually captures more road and less sky.

Check Field of View and Stability Settings

Set the recording resolution and field of view before you ride, not while stopped on the shoulder. Turn on the stabilization setting your model offers, and record a short test clip at a few speeds to confirm the image is level and the mount is not vibrating.

Before-Ride Safety Checklist

Mount is fully cured and does not wiggle when pushed.
Camera cannot fall off or swing into your field of view.
Visor and vents move freely and close fully.
Helmet fits snugly with no added pressure points from the mount.
Cables and batteries are secured and not dangling.

Common Mistakes to Avoid

Mounting over a vent or seam, which can lift the mount in wind.
Using an adhesive pad on a dirty or oily surface.
Tilting the lens too high and recording mostly sky.
Forgetting to check the mount after the first ride, when vibration may have loosened it.
Installing a camera that changes the helmet’s balance or fit enough to cause neck strain.

Recommended Gear

GoPro Chin Mount: A chin-area mount that keeps the lens close to your natural line of sight for motorcycle footage. View on Amazon
GoPro Helmet Front Mount: A front-facing bracket that places the camera high on the helmet for a wider view of the road. View on Amazon
Rubbing alcohol and microfiber cloth: Used to degrease the shell before applying any adhesive mount. View on Amazon

FAQ

Can I use a GoPro on any motorcycle helmet?

Most helmets accept some form of GoPro mount, but the shape of the shell determines which mount fits safely. Check the mount’s compatibility notes against your helmet type before buying.

Will a helmet camera affect my helmet’s safety rating?

Attaching a mount with adhesive or straps does not usually alter the certified shell, but drilling or modifying it can. Consult your helmet manufacturer if you have doubts about a specific setup.

Should I stabilize the camera with a longer mount?

A longer mount can raise the camera and reduce vibration in some setups, but it also adds leverage and wind load. Test the setup on a short ride before committing to a long-distance trip.

Conclusion

A secure GoPro helmet setup comes down to a compatible mount, a clean and fully cured attachment, and a lens angle that keeps the road in view. Run the safety checklist before every ride and recheck the mount after the first few miles. Once it’s set, you can focus on the ride and let the camera do the recording.

Ready to choose one?

About Claire Whitaker

Claire Whitaker is part of our editorial team and reviews and edits our motorcycle riding gear guides, checking product details against manufacturer specifications and owner feedback.

About the author

Claire Whitaker

Claire Whitaker writes reviews and buying guides for Max Motorcycle Videos.